Obvesti me
Artikla trenutno ni na zalogi. Spodaj se lahko prijavite in poslali vam bomo obvestilo, takoj ko artikel prispe na zalogo. Obvestilo boste dobili samo za ta artikel.
Vaš email naslov:
  CAPTCHA Image
Varnostna koda:

Iskanje
Slovenski
Slovenski
Hrvatski
English
Deutsch
Italiano
Srpski
Prijava Registracija
NOVI ARTIKLI
AKCIJE
NAJBOLJ PRODAJANI
Stroški dostave
Izberi državo
Austria
Belgium
Bosnia and Herzegovina
Bulgaria
Canada
Croatia
Cyprus
Czech Republic
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Ireland
Italy
Latvia
Lithuania
Luxembourg
Malta
Montenegro
Netherlands
Poland
Portugal
Romania
Serbia
Slovakia
Slovenia
Spain
Sweden
United Kingdom
Pošta Slovenije 3.00 EUR
 
Informacije
Pogoji in informacije
Vprašajte nas
Galago elektronika
Galago d.o.o.
Trg svobode 20
2390 Ravne na Koroškem
Slovenija
E-pošta: info@galago.si
Telefon: 00386 (0)2 620 08 14
Telefon: 00386 (0)40 559 432
Facebook

SMALL REDUCTION STEPPER MOTOR - 5VDC 32-STEP 1 - 16 GEARING, ADAFRUIT 858

  Id številka: 1018
Znamka:ADAFRUIT
Zaloga:   DA
Cena:6,64 €
robotics ADAFRUIT Small Reduction Stepper Motor - 5VDC 32-Step 1 - 16 Gearing, adafruit 858
robotics ADAFRUIT Small Reduction Stepper Motor - 5VDC 32-Step 1 - 16 Gearing, adafruit 858
robotics ADAFRUIT Small Reduction Stepper Motor - 5VDC 32-Step 1 - 16 Gearing, adafruit 858
robotics ADAFRUIT Small Reduction Stepper Motor - 5VDC 32-Step 1 - 16 Gearing, adafruit 858
 

 

DESCRIPTION



This is a great first stepper motor, good for small projects and experimenting with steppers. This uni-polar motor has a built in mounting plate with two mounting holes. There are only 32 step (11.25 degree) per revolution, and inside is a 1/16 reduction gear set. (Actually its 1/16.032 but for most purposes 1/16 is a good enough approximation) What this means is that there are really 32*16.032 steps per revolution = 513 steps! The shaft is flattened so its easy to attach stuff to it with a set-screw. A perfect first stepper motor and works well with the Motor Shield for Arduino.

 

The gearing has a few side effects which are important to note. First, you can turn the stepper by hand but not as smoothly as an un-geared stepper. It also means you shouldn't use interleaved or micro-stepping to control or it will take forever to turn. Instead use single or double stepping. The torque is fairly high but its slower than un-geared steppers - we maxed out at about 50 RPM by over-driving it a bit with 9VDC. At 5V try to stick to under 25 RPM.

 

To use with the Adafruit Motor Shield, connect red to ground (middle), orange and pink to one motor port (say M1) and blue and yellow to the other motor port (say M2). So in order, thats: orange - pink - red - blue - yellow. Then just use the example code that comes with the Adafruit Motor Shield library and set the constructor to Adafruit_StepperMotor *myMotor = AFMS.getStepper(513,motornum) and the speed at 5 RPM by calling motor->setSpeed(5). Otherwise, you can also wire it up with some transistors and use the Arduino Stepper library.

 

 

TECHNICAL DETAILS

- Unipolar stepper with 0.1" spaced 5-pin cable connector

- 513 steps per revolution

- 1/16.032 geared down reduction

- 5V DC suggested operation

- Weight: 37 g.

- Dimensions: 28mm diameter, 20mm tall not including 9mm shaft with 5mm diameter

- 9" / 23 cm long cable

- Holding Torque: 150 gram-force*cm, 15 N*mm/ 2 oz-force*in

- Shaft: 5mm diameter flattened

- Approx 42 ohm DC impedence per winding