Obvesti me
Artikla trenutno ni na zalogi. Spodaj se lahko prijavite in poslali vam bomo obvestilo, takoj ko artikel prispe na zalogo. Obvestilo boste dobili samo za ta artikel.
Vaš email naslov:

Iskanje
Slovenski
Slovenski
Hrvatski
English
Deutsch
Italiano
Srpski
Prijava Registracija
NOVI ARTIKLI
AKCIJE
NAJBOLJ PRODAJANI
Stroški dostave
Izberi državo
Austria
Belgium
Bosnia and Herzegovina
Bulgaria
Canada
Croatia
Cyprus
Czech Republic
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Ireland
Italy
Latvia
Lithuania
Luxembourg
Macedonia, the former Yugoslav Republic of
Malta
Montenegro
Netherlands
Poland
Portugal
Romania
Serbia
Slovakia
Slovenia
Spain
Sweden
United Kingdom
Pošta Slovenije 3.00 EUR
 
Informacije
Pogoji in informacije
Vprašajte nas
Galago elektronika
Galago d.o.o.
Gačnikova pot 2
2390 Ravne na Koroškem
Slovenija
E-pošta: info@galago.si
Telefon: 00386 (0)8 205 08 77
Telefon: 00386 (0)40 559 432
Facebook

SPARKFUN BLUETOOTH MATE GOLD, SPARK FUN 12580

  Id številka: 1021/
Znamka:SPARKFUN
Zaloga:   DA
Cena:32,21 €
 SPARKFUN SparkFun Bluetooth Mate Gold, spark fun 12580
 SPARKFUN SparkFun Bluetooth Mate Gold, spark fun 12580
 SPARKFUN SparkFun Bluetooth Mate Gold, spark fun 12580
 SPARKFUN SparkFun Bluetooth Mate Gold, spark fun 12580
 SPARKFUN SparkFun Bluetooth Mate Gold, spark fun 12580
 

 

Description: The Bluetooth Mate Gold is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduinos. These modems work as a serial (RX/TX) pipe, and are a great wireless replacement for serial cables. Any serial stream from 2400 to 115200bps can be passed seamlessly from your computer to your target. We’ve tested these units successfully over open air at 350ft (106m)!

 

Bluetooth Mate has the same pin out as the FTDI Basic, and is meant to plug directly into an Arduino Pro, Pro Mini, or LilyPad Mainboard. Because we’ve arranged the pins to do this, you cannot directly plug the Bluetooth Mate to an FTDI Basic board (you’ll have to swap TX and RX).

 

This unit ships with an RN-41 class 1 bluetooth module, a very easy-to-use and well documented bluetooth module. Make sure you check out the datasheet and command set links below. If you don’t need the extra range, check out the Bluetooth Mate Silver which uses a Class 2 module which has less range.

 

The Bluetooth Mate has on-board voltage regulators, so it can be powered from any 3.3 to 6VDC power supply. Spark fun’ve got level shifting all set up so the RX and TX pins on the remote unit are 3-6VDC tolerant. Do not attach this device directly to a serial port. You will need an RS232 to TTL converter circuit if you need to attach this to a computer.

 

Unit comes without a connector; if you want to connect it to an Arduino Pro, spark fun’d suggest the 6-pin right-angle female header.

 

Note: If you are looking for the ability to use the FTDI directly with your Bluetooth Mate check out our Crossover Breakout for FTDI!

 

Note: The hardware reset pin of the RN-41 module is broken out on the bottom side of the board. This pin is mislabeled as ‘PIO6’, it is actually PIO4. Should you need to reset the Mate, pull this pin high upon power-up, and then toggle it 3 times.

 

Features:

- v6.15 Firmware

- Designed to work directly with Arduino Pro’s and LilyPad main boards

- FCC Approved Class 1 Bluetooth® Radio Modem

- Very robust link both in integrity and transmission distance (100m) - no more buffer overruns!

- Low power consumption : 25mA avg

- Hardy frequency hopping scheme - operates in harsh RF environments like WiFi, 802.11g, and Zigbee

- Encrypted connection

- Frequency: 2.402~2.480 GHz

- Operating Voltage: 3.3V-6V

- Serial communications: 2400-115200bps

- Operating Temperature: -40 ~ +70C

- Built-in antenna

 

Dimensions:

- Board: 1.75x0.65"

 

Documents:

- Schematic

- RN-41 AT Command Set v6.15

- RN-41 Datasheet

- Hookup Guide

- Bluetooth Primer

- GitHub