Obvesti me
Artikla trenutno ni na zalogi. Spodaj se lahko prijavite in poslali vam bomo obvestilo, takoj ko artikel prispe na zalogo. Obvestilo boste dobili samo za ta artikel.
Vaš email naslov:
  CAPTCHA Image
Varnostna koda:

Iskanje
Slovenski
Slovenski
Hrvatski
English
Deutsch
Italiano
Srpski
Prijava Registracija
NOVI ARTIKLI
AKCIJE
NAJBOLJ PRODAJANI
Stroški dostave
Izberi državo
Austria
Belgium
Bosnia and Herzegovina
Bulgaria
Canada
Croatia
Cyprus
Czech Republic
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Ireland
Italy
Latvia
Lithuania
Luxembourg
Malta
Montenegro
Netherlands
Poland
Portugal
Romania
Serbia
Slovakia
Slovenia
Spain
Sweden
United Kingdom
Pošta Slovenije 3.00 EUR
 
Informacije
Pogoji in informacije
Vprašajte nas
Galago elektronika
Galago d.o.o.
Trg svobode 20
2390 Ravne na Koroškem
Slovenija
E-pošta: info@galago.si
Telefon: 00386 (0)2 620 08 14
Telefon: 00386 (0)40 559 432
Facebook

ADAFRUIT PRO TRINKET - 3V 12MHZ, ADAFRUIT 2010

  Id številka: 1586
Znamka:ADAFRUIT
Zaloga:   DA
Cena:13,36 €
trinket ADAFRUIT Adafruit Pro Trinket - 3V 12MHz, ADAFRUIT 2010
trinket ADAFRUIT Adafruit Pro Trinket - 3V 12MHz, ADAFRUIT 2010
trinket ADAFRUIT Adafruit Pro Trinket - 3V 12MHz, ADAFRUIT 2010
trinket ADAFRUIT Adafruit Pro Trinket - 3V 12MHz, ADAFRUIT 2010
trinket ADAFRUIT Adafruit Pro Trinket - 3V 12MHz, ADAFRUIT 2010
 

 

 

DESCRIPTION

 

The Pro Trinket PCB measures only 1.5" x 0.7" x 0.2" (without headers) but packs the same capability as an Arduino UNO. So it's great once you've finished up a prototype on an official Arduino UNO and want to make the project smaller.

 

The Pro Trinket 3V uses the Atmega328P chip, which is the same core chip in the Arduino UNO/Duemilanove/Mini/etc. However, it uses 3V logic and 12MHz clock which means it's good when you want a lower-power and lower-voltage setup. Pro Trinket is programmable using the Arduino IDE as you already set up, and 95% of Arduino projects will work out of the box!

 

 

Here's some things you may have to consider when adapting Arduino sketches:

 

- Pins #2 and #7 are not available (they are exclusively for USB)

- The Pro Trinket 3V runs at 12MHz, this doesn't affect most projects. Only the most timing-specific libraries may be affected, check the documentation! The NeoPixel Library works fine at 12MHz.

- The onboard power supply is a 3.3V regulator and it can provide 150mA output

- You cannot plug shields directly into the Pro Trinket

- There is no Serial-to-USB chip onboard. This is to keep the Pro Trinket small and inexpensive, you can use any FTDI cable to connect to the FTDI port for a Serial connection. The USB connection is for uploading new code only.

- The bootloader on the Pro Trinket use 4KB of FLASH so the maximum sketch size is 28,672 bytes. The bootloader does not affect RAM usage.

 

 

Here's some handy specifications:

 

- ATmega328P onboard chip in QFN package running at 3.3V logic

- 12MHz clock rate, 28K FLASH available

- USB bootloader with a nice LED indicator looks just like a USBtinyISP so you can program it with AVRdude and/or the Arduino IDE (with a few simple config modifications).

- Also has headers for an FTDI port for reprogramming

- Micro-USB jack for power and/or USB uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram.

- On-board 3.3V power regulator with 150mA output capability and ultra-low dropout. Up to 16V input, reverse-polarity protection, thermal and current-limit protection.

- Power with either USB or external output (such as a battery) - it'll automatically switch over

- On-board green power LED and red pin #13 LED

- Reset button for entering the bootloader or restarting the program.

- Works with 99% of existing Arduino sketches (anything that doesn't use more than 28K, and doesn't require pins #2 and #7)

 

 

TECHNICAL DETAILS

 

Dimensions:

 

38mm x 18mm x 2mm / 1.5" x 0.7" x 0.08"

Height with MicroUSB: 4mm / 0.16"

Weight: 2.6g

 

Datasheets, documents, Fritzing objects, PCB files and more are in the tutorial